![]() ![]() Your project should now be a lot lighter and more workable.Ĭhances are you hopefully won’t be in the situation where you’ll need to utilise this tip if you’ve planned your Revit project effectively.LAUNCH X431 O2-1 Scopebox Oscilloscope, an optional add-on module which turns your X-431 Throttle and X-431 PAD II into a 4 channel Lab Scope. By analyzing waveforms, a variety of faults on sensors, actuators, circuits and electronic control units can be discovered – saving time on vehicle diagnosis and cutting down on unnecessary parts replacement costs. HOUGE STOCK, THREADED 22 INCH BARREL, SCOPE, BOX, AND DOCS 749. You can manually initiate the installation by selecting Install Additional Software from the ScopeBox menu. You can either go and edit each one of these elements, or just use the same method of selecting the scope box and creating a section with the Coins auto-section box add-in. Installation into our chassis design is incredibly easy as well with just two screws. You will notice that any elements which are attached to this view will also remain (floor slabs + walls which were associated with the selected elements). misuse, normal wear and tear, or by improper handling or installation, and the warranty is voided by. You will now be left with the elements you want to work with, and a much lighter project. I followed the Warrinty card in the scope box. Once you have done this, click on your light bulb icon and unhide all elements in view. Highlight all the remaining elements and delete them. You should now see the rest of your building MINUS the elements that you want to work with. Staying in the same view, go to your ‘Properties’ palette and turn off your section box. The section box and all elements inside will now be hidden. Now you will want to click on ‘Hide Element’. Did you ever figure this out (5 years ago). ![]() All relevant visibility options are set: workset is visible, its visible through visibility settings, its not hiddent in view, there are no filters applied, view plane is within its extents. If you can see other elements that were also selected in your view at this point you can shift de-select all these. Im trying to create a scope box and when I pick the two corners it does not show up. We will now want to highlight this whole area including all elements in the scope box. Waveform auto-set up on all of the 4 channels. You should now have the selected area of your building isolated in a section box. Scopebox features: Contains an integrated library of standard waveforms. 4-5 4.4 Waveform analysis mode The ignition secondary single-cylinder waveform test is mainly used to: Analyze the ignition dwell angle of single cylinder.(ignition coil charging time) Analyze the capability of ignition coil and secondary high tension circuit (from ignition line to ignition voltage. ScopeBox for Mac By Divergent Media Free to try Download Now Key Details of ScopeBox Turn your Mac into a preview monitor, direct to disk recorder, and video QA toolkit Last updated on 05/18/20. Name your view and either give a custom size or as I usually do, select the ‘Element extents, plus buffer’ 300mm is the default (giving you a 300mm tolerance on each side of the selected elements). LAUNCH X431 PAD Scopebox User’s Manual Fig. Select the scope box, go to the ‘Add-Ins’ tab and click ‘Auto Section Box’. Scope boxes can also be used to control the extents of the views themselves. Once you have done this, we will use the ‘Coins Auto-Section box’ add-in to isolate the scope box, just giving us the area of the building that we want to display / work with. Use a scope box to control the extent of any datum element such as grids, levels and reference planes. Go to the ‘View’ tab and select ‘Scope box’ create your box on a floor plan and ensure that the vertical extents are at the desired position on a 3D view. Setting up worksets to narrow down the elements by cores is also an option, but unless you have set the project up with this in mind, it could take a while to set up and re-edit all your worksets.Īn option which me and my colleague Johnny Furlong discovered is making use, yet again of the amazing ‘ Coins Auto-Section Box‘ (which is quickly becoming my favourite and most used Revit add-in!).įor this example I will use the Revit sample project as I’m not able to post information on the project we needed to do this on. Using a section box will give you the desired visual effect but the project will still be as heavy as it was prior to narrowing down the view to only show the elements you are presenting / working with. Ever had a Revit project which is so large that you are having performance issues and trouble working on it? Want to work on a specific area of the building (possibly cores) without being slowed down by the data in the rest of the building? If you do then the View Template has a very limited use across the project, especially for large projects. ![]()
0 Comments
Leave a Reply. |